-
Product Description Edwards EST SIGA-DG Detector Guard -
Product Description NOTE: This part is discontinued by the manufacturer. Replace with: SIGA-HRD The Edwards EST SIGA-HRS Heat Detector is a combination 15°F per minute Rate-of-Rise, and 135°F (57°C) Fixed-Temperature Heat Detector. Edwards EST SIGA-HRS detectors are compatible only with Signature Loop Controller. COMPATIBLE BASES and ACCESSORIES: — SIGA-SB Detector Mounting Base - Standard — SIGA-SB4 4-inch Detector Mounting Base w/ SIGA-TS4 Trim Skirt — SIGA-RB Detector Mounting Base w/Relay — SIGA-RB4 4-inch Detector Mounting Base w/Relay w/ SIGA-TS4 Trim Skirt — SIGA-IB Detector Mounting Base w/Fault Isolator — SIGA-IB4 4-inch Detector Mounting Base w/ Fault Isolator and SIGA-TS4 Trim Skirt — SIGA-LED Remote Alarm LED. (Connects to the SIGA-SB or SIGA-SB4 Standard Base only.) — SIGA-AB4G Audible (Sounder) Base for Fire Detectors — SIGA-AB4GT Audible (Sounder) Base for CO and Fire Detectors — SIGA-TCDR Temporal Pattern Generator — SIGA-CRR Polarity Reversal Relay can be used for sounding to other audible bases on the same 24 Vdc circuit. — SIGA-TS4 Trim Skirt (supplied with 4-inch bases) — SIGA-DMP Detector Mounting Plate — SIGA-RTA Detector Removal Tool — SIGA-VA Detector Cleaning Tool NOTE: This part replaces SIGA2-HRS and SIGA-HRD.
-
Product Description NOTE: This part is discontinued by the manufacturer. The EST SIGA-IPHS Intelligent 4D Multisensor Detector is a combination Ionization, Photoelectric, and Thermal Boost Type Smoke Detector. EST SIGA-IPHS detectors are compatible only with Signature Loop Controller. COMPATIBLE BASES and ACCESSORIES: — SIGA-SB Detector Mounting Base - Standard — SIGA-SB4 4-inch Detector Mounting Base w/ SIGA-TS4 Trim Skirt — SIGA-RB Detector Mounting Base w/Relay — SIGA-RB4 4-inch Detector Mounting Base w/Relay w/ SIGA-TS4 Trim Skirt — SIGA-IB Detector Mounting Base w/Fault Isolator — SIGA-IB4 4-inch Detector Mounting Base w/ Fault Isolator and SIGA-TS4 Trim Skirt — SIGA-LED Remote Alarm LED. (Connects to the SIGA-SB or SIGA-SB4 Standard Base only.) — SIGA-AB4G Audible (Sounder) Base for Fire Detectors — SIGA-AB4GT Audible (Sounder) Base for CO and Fire Detectors — SIGA-TCDR Temporal Pattern Generator — SIGA-CRR Polarity Reversal Relay can be used for sounding to other audible bases on the same 24 Vdc circuit. — SIGA-TS4 Trim Skirt (supplied with 4-inch bases) — SIGA-DMP Detector Mounting Plate — SIGA-RTA Detector Removal Tool — SIGA-VA Detector Cleaning Tool
-
Product Description NOTE: This part is discontinued by the manufacturer. Replace with: SIGA-PHD. Edwards EST SIGA-PHS Intelligent 3D Multisensor Detector is a combination Photoelectric Smoke and Fixed-Temperature Heat Detector, compatible only with EST’s Signature Loop Controller. COMPATIBLE BASES and ACCESSORIES: — SIGA-SB Detector Mounting Base - Standard — SIGA-SB4 4-inch Detector Mounting Base w/ SIGA-TS4 Trim Skirt — SIGA-RB Detector Mounting Base w/Relay — SIGA-RB4 4-inch Detector Mounting Base w/Relay w/ SIGA-TS4 Trim Skirt — SIGA-IB Detector Mounting Base w/Fault Isolator — SIGA-IB4 4-inch Detector Mounting Base w/ Fault Isolator and SIGA-TS4 Trim Skirt — SIGA-LED Remote Alarm LED. (Connects to the SIGA-SB or SIGA-SB4 Standard Base only.) — SIGA-AB4G Audible (Sounder) Base for Fire Detectors — SIGA-AB4GT Audible (Sounder) Base for CO and Fire Detectors — SIGA-TCDR Temporal Pattern Generator — SIGA-CRR Polarity Reversal Relay can be used for sounding to other audible bases on the same 24 Vdc circuit. — SIGA-TS4 Trim Skirt (supplied with 4-inch bases) — SIGA-DMP Detector Mounting Plate — SIGA-RTA Detector Removal Tool — SIGA-VA Detector Cleaning Tool NOTE: This part replaces SIGA2-PHS for applications that do not require split photo/heat operation.
-
Product Description NOTE: This part is discontinued by the manufacturer. Replace with: SIGA-PD The Edwards EST SIGA-PS Intelligent Photoelectric Smoke Detectors is part of the Signature Series Detection and Alarm equipment from Edwards / EST. The Edwards EST SIGA-PS is compatible for use only with EST’s Signature Loop Controller. Uses one Device Address. COMPATIBLE BASES and ACCESSORIES: — SIGA-SB Detector Mounting Base - Standard — SIGA-SB4 4-inch Detector Mounting Base w/ SIGA-TS4 Trim Skirt — SIGA-RB Detector Mounting Base w/Relay — SIGA-RB4 4-inch Detector Mounting Base w/Relay w/ SIGA-TS4 Trim Skirt — SIGA-IB Detector Mounting Base w/Fault Isolator — SIGA-IB4 4-inch Detector Mounting Base w/ Fault Isolator and SIGA-TS4 Trim Skirt — SIGA-LED Remote Alarm LED. (Connects to the SIGA-SB or SIGA-SB4 Standard Base only.) — SIGA-AB4G Audible (Sounder) Base for Fire Detectors — SIGA-AB4GT Audible (Sounder) Base for CO and Fire Detectors — SIGA-TCDR Temporal Pattern Generator — SIGA-CRR Polarity Reversal Relay can be used for sounding to other audible bases on the same 24 Vdc circuit. — SIGA-TS4 Trim Skirt (supplied with 4-inch bases) — SIGA-DMP Detector Mounting Plate — SIGA-RTA Detector Removal Tool — SIGA-VA Detector Cleaning Tool
-
Product Description NOTE: This part is discontinued by the manufacturer. Replace with: SIGA-PCD The Edwards EST Signature Series SIGA2-PCOS Intelligent Photoelectric Detector with carbon monoxide sensor is compatible for use with the Signature Loop Controller. COMPATIBLE BASES and ACCESSORIES: — SIGA-SB Detector Mounting Base - Standard — SIGA-SB4 4-inch Detector Mounting Base w/ SIGA-TS4 Trim Skirt — SIGA-RB Detector Mounting Base w/Relay — SIGA-RB4 4-inch Detector Mounting Base w/Relay w/ SIGA-TS4 Trim Skirt — SIGA-IB Detector Mounting Base w/Fault Isolator — SIGA-IB4 4-inch Detector Mounting Base w/ Fault Isolator and SIGA-TS4 Trim Skirt — SIGA-LED Remote Alarm LED. (Connects to the SIGA-SB or SIGA-SB4 Standard Base only.) — SIGA-AB4G Audible (Sounder) Base for Fire Detectors — SIGA-AB4GT Audible (Sounder) Base for CO and Fire Detectors — SIGA-TCDR Temporal Pattern Generator — SIGA-CRR Polarity Reversal Relay can be used for sounding to other audible bases on the same 24 Vdc circuit. — SIGA-TS4 Trim Skirt (supplied with 4-inch bases) — SIGA-DMP Detector Mounting Plate — SIGA-RTA Detector Removal Tool — SIGA-VA Detector Cleaning Tool — 2-SPRC2 Replacement Smoke Chamber — 2-CORPL Replacement CO Sensor
-
Product Description NOTE: This part is discontinued by the manufacturer. Replace with SIGA-PD. Edwards EST SIGA2-PS Intelligent Photoelectric Smoke Detectors are only for use with Signature Loop Controller. COMPATIBLE BASES and ACCESSORIES: — SIGA-SB Detector Mounting Base - Standard — SIGA-SB4 4-inch Detector Mounting Base w/ SIGA-TS4 Trim Skirt — SIGA-RB Detector Mounting Base w/Relay — SIGA-RB4 4-inch Detector Mounting Base w/Relay w/ SIGA-TS4 Trim Skirt — SIGA-IB Detector Mounting Base w/Fault Isolator — SIGA-IB4 4-inch Detector Mounting Base w/ Fault Isolator and SIGA-TS4 Trim Skirt — SIGA-LED Remote Alarm LED. (Connects to the SIGA-SB or SIGA-SB4 Standard Base only.) — SIGA-AB4G Audible (Sounder) Base for Fire Detectors — SIGA-AB4GT Audible (Sounder) Base for CO and Fire Detectors — SIGA-TCDR Temporal Pattern Generator — SIGA-CRR Polarity Reversal Relay can be used for sounding to other audible bases on the same 24 Vdc circuit. — SIGA-TS4 Trim Skirt (supplied with 4-inch bases) — SIGA-DMP Detector Mounting Plate — SIGA-RTA Detector Removal Tool — SIGA-VA Detector Cleaning Tool
-
Product Description The Edwards TSD-SJ-C01 is a SuperDuct Four-Wire Duct Smoke Detector with RJ-45 modular connector. Includes carbon monoxide (CO1) sensor.module COMPATIBLE ACCESSORIES: — SD-T8 8-inch sampling tube — SD-T18 18-inch sampling tube — SD-T24 24-inch sampling tube — SD-T36 36-inch sampling tube — SD-T42 42-inch sampling tube — SD-T60 60-inch sampling tube — SD-T78 78-inch sampling tube — SD-T120 120-inch sampling tube — SD-RJ5 RJ-45 wiring harness kit, 5.0 ft — SD-RJ10 RJ-45 wiring harness kit, 10.0 ft — SD-RJ15 RJ-45 wiring harness kit, 15.0 ft — SD-RJ20 RJ-45 wiring harness kit, 20.0 ft. — SD-TRM4 Remote test-reset station, magnetic — SD-TRK4 Remote test-reset station, keyed — SD-MAG Test magnet kit — SD-TMP Sampling tube mounting plate — SD-VTK Air velocity test kit — SD-GSK Cover gasket kit
-
Product Description The EST APS4-B is the Auxiliary Power Supply for the IRC-3 FACP.
-
Key Features
- EN137:2006 Type 2 MED Approved Breathing Apparatus
- Compliance set for Marine and Industrial firefighting environments
- Rigid backframe construction
-
Key Features
- Proven high performance pneumatic system
- Compact first breath activated demand valve with bypass
- Ergonomically designed lightweight backplate and type 2 harness
-
Key Features
- EN137:2006 Type 2 MED Approved Breathing Apparatus
- Compliance set for Industrial Professional Fire Fighting or Oil & Gas markets
- Rigid backframe construction
-
Key Features
- EN137:2006 Type 2, MED Approved Breathing Apparatus
- Designed for use by the Fire Service or the Oil & Gas market
- Rigid backframe construction
-
Key Features
- EN137:2006 Type 2 MED Approved Breathing Apparatus
- Designed specifically for use by the Professional Fire Service
- Rigid backframe construction with adjustable backplate
-
Key Features
- Approved to EN137: 2006 Type II, incorporating the stringent Flame Engulfment Test
- 100% Kevlar webbing with wrap-around harnesses
- The highest possible specification providing the highest level of flame retardancy
-
The 3M Scott Safety ProPak-F-EZ-FLO is a Type 2 open circuit, self-contained, compressed air breathing apparatus. It consists of a back plate, padded carrying harness and pneumatic system, containing a cylinder connector, reducer, pressure gauge, whistle and demand valve. The ProPak-F-EZ-FLO can be configured in a number of different ways with various size single cylinders. There are also a range of variants available including Airline (AC), Split Demand Valve Coupling (SDC or Y2C), Quick Connect Option or Duo variants. The ProPak-F-EZ-FLO is used in conjunction with AV3000HT facemask and a choice of composite or steel cylinders.
-
The 3M Scott Safety ProPak-FX-EZ-FLO is a Type 2 open circuit, self-contained, compressed air breathing apparatus. It consists of a back plate, padded carrying harness and pneumatic system, containing a cylinder connector, reducer, pressure gauge, whistle and demand valve. The ProPak-FX-EZ-FLO can be configured in a number of different ways with various size single cylinders. There are also a range of variants available including Airline (AC), Split Demand Valve Coupling (SDC or Y2C), Quick Connect Option or Duo variants. The ProPak-FX-EZ-FLO is used in conjunction with AV3000HT facemask and a choice of composite or steel cylinders. APPLICATIONS The ProPak-FX-EZ-FLO is specifically designed as a professional fire fighting SCBA, but is also suitable for providing respiratory protection in any IDLH environment.
-
The Cen-Paq is ideal for situations where speed of response is required or it can be worn for a shift with the facemask stowed in its pouch to be used when necessary. Suitable for snatch rescue, intervention and rescue applications where a full sized SCBA may be too bulky. CE marked in accordance with EN137 and also EN139 when fitted with an airline attachment. TECHNICAL DESCRIPTION The Cen-Paq is a waistcoat mounted short duration self contained breathing apparatus. It comprises of a waistcoat, a high pressure air cylinder and a two stage pneumatic system with pressure reducer and demand valve. The full face mask (Promask PP or Vision 3) and cylinder are purchased separately. The full face mask (Promask PP or Vision 3) used with the Cen-Paq in conjunction with the high performance demand valve ensures that positive pressure is maintained within the facepiece, thus providing the highest level of respiratory protection. The cylinder is mounted in a pouch on the back of the jacket. The two versions of cylinder allow a total duration of 15, 20 or 30 minutes when used at an average wearer consumption rate of 40L/min. The Cen-Paq utilises a waistcoat fabricated from high visibility PVC and features a double breasted velcro fastening system. The waistcoat is designed to fit a wide range of body sizes with minimal adjustment required. Anti-static jacket options are also available.
-
Key Features
- Single or Twin Cylinders
- Simple Maintenance
- Low Through-Life Costs
-
Key Features
- Approved to EN137: 2006 Class II, incorporating the stringent flame engulfment test
- Lightest BA set in its class3 point adjustable backplate
- Proven Tempest Demand Valve
-
Key Features
- Lightweight and reliable with a good service life
- Carrying system offers excellent load distribution
- Compatible with proven and robust air supply systems
- Innovative space-frame integrating the hoses to eliminate entanglement and reduce snagging
- Easy to clean and maintain service friendly design
-
Today's first responders demand reliability and consistency from their breathing apparatus whatever the environmental conditions. Resulting from years of research and extensive user consultation, the Drager PSS 3000 has been developed to meet these fundamental needs:
-
The Drager PSS 4000 is one of the lightest professional self-contained breathing apparatus available for firefighters. Combining comfort with exceptional pneumatic performance, the PSS 4000 SCBA is designed for applications where simplicity and ease of use are crucial. Lightweight yet robust, and easy to don, the PSS® 4000 provides outstanding breathing protection.
-
The Drager PSS 5000 SCBA is a new generation high performance breathing apparatus for the professional firefighter. Combining advanced ergonomics with a wide range of configurable options the Drager PSS 5000 provides the user with the comfort and versatility to meet the demands of first responders whenever breathing protection is required.
