-
Product Description The Edwards 874-G5 Vibrating Horn is designed for surface mounting. Adjustable output: 88 to 113dB @ 1m (78 to 103dB @ 10ft.) Power: 24VAC, 0.63 A Also available: 872-PO AdaptaHorn Plastic projector snaps onto any AdaptaHorn. Sold separately. -
Product Description Edwards 879EX-E1 Adaptahorn is a heavy-duty, high decibel, vibrating horn signal designed for use in hazardous locations. 12VDC Operating voltage with wide operating voltage range -20% to +10% of nominal voltage. Power connection wires embedded in sealing compound Two mounting brackets are provided on either side of the unit for wall mounting. The housing is tapped on one side for 3/4" conduit to allow for field wiring installation.
-
Product Description Edwards 881ALD-AW Flush Horn
-
Product Description Edwards 8ZEXP 8 Zone Expansion Module The 8 Zone Expansion Module for LSS4 Fire Alarm Control Panel. Class B and open collector circuit per zone.
-
Product Description The Edwards 98BR-G1 is an Adapt-A-Beacon Light Duty Strobe. FEATURES and SPECIFICATIONS: Voltage: 24 VDC Color: Red Lamp Type: Strobe Flash Rate/Minute: 65 Mounting: Conduit;Direct
-
Product Description Edwards EST A60U2 Line Isolator Module
-
Product Description Edwards EST B4U Detector Base is intended for use with these Analog Addressable Detectors from GE's Edwards Signalling and Security Systems: — E-HD Heat Detector — E-PHD Photoelectric/Heat Detector — E-PD Photoelectric Detector — E-PDD Duct Detector
-
Product Description The EST BPS-10A Booster Power Supply (10 amp) is designed to extend the signaling capacity of a fire alarm, security, or access control system. The BPSs can be connected to existing Class A or Class B notification appliance circuits (NACs) or activated via option modules. The BPSs can either pass or generate synchronization signals for Genesis sync strobes. The BPSs have four independent NAC / AUX circuits that are supervised when configured for NAC, plus a trouble relay. The input circuits of the booster power supply can be connected to 12 VDC or 24 VDC systems.
-
-
Product Description The EST BPS-10A Booster Power Supply (10 amp) is designed to extend the signaling capacity of a fire alarm, security, or access control system. The BPSs can be connected to existing Class A or Class B notification appliance circuits (NACs) or activated via option modules. The BPSs can either pass or generate synchronization signals for Genesis sync strobes. The BPSs have four independent NAC / AUX circuits that are supervised when configured for NAC, plus a trouble relay. The input circuits of the booster power supply can be connected to 12 VDC or 24 VDC systems.
-
Product Description This is the Replacement Board for the Edwards EST BPS6A Booster Power Supply (6.5 amp) is designed to extend the signaling capacity of a fire alarm, security, or access control system. The BPSs can be connected to existing Class A or Class B notification appliance circuits (NACs) or activated via option modules. The BPSs can either pass or generate synchronization signals for Genesis sync strobes. The BPSs have four independent NAC/AUX circuits that are supervised when configured for NAC, plus a trouble relay. The input circuits of the booster power supply can be connected to 12 VDC or 24 VDC systems.
-
Product Description The Edwards EST C-DTS is a Detector Test Station, single-gang, flush mount.
-
Product Description The Edwards CF200-EWT is an Explosion-Proof Fixed Temperature Heat Detector. Model CF-200-EWT is rated for 200F (93C) Contacts: Single Pole Normally Open - Rated at: 3.0 amps at 6 to 125VAC; 1.0 amps at 6 to 28VDC; 0.3 amps at 125VDC; 0.1 amp at 250VDC.
-
Product Description The Edwards EST CRB4U-1 is a 4" relay detector base (1.25A @ 30 Vdc) for use with Edwards EST EC Series of Smoke and Heat Detectors.
-
Product Description Edwards CS2002-11 Manual Yellow Pull Station
-
Product Description NOTE: This part is discontinued by the manufacturer. There is no designated replacement. The Edwards DLD Dual Line Dialer provides two telephone line connections for transmitting system status changes to one or two compatible digital alarm communicator receivers (DACRs) over the public switched telephone network. For use with QS FACPs.
-
Product Description Edwards E-IDC1A Analog Class A Single Input Module is an analog addressable device used to connect a normally open, alarm, supervisory, or monitor type dry contact initiating device circuit (IDC) to a control panel. This module is designed for Class A circuit operation. The device address is set using the two rotary switches located on the front of the module. One device address is required. The device can be preset for alarm or supervisory operation using the slide switch located on the front of the module. The module can also be configured for other device types through front panel programming or the configuration utility.
-
Product Description The Edwards E-IDC1B Analog Single Input Mini Module connects a normally open, alarm, supervisory, or monitor type dry contact initiating device circuit (IDC) to the Edwards Signaling control panel. For Class B circuit operation.
-
Product Description The Edwards E-PD Intelligent Analog Optical Smoke Detector uses rotary switches to set address. COMPATIBLE BASES and ACCESSORIES: — B4U Standard Base — RB4U Relay Detector Base — IB4U Isolator Detector Base — SB4U Audible (Sounder) Detector Base — AB4G-SB Surface Box for Audible Base — RLED Remote alarm LED, use with standard base only — 211-10PKG Replacement optical chambers
-
Product Description Edwards EC-100R Beam Detector Unit
-
Product Description Edwards EST EC-LLT Low Level Tester
-
Product Description The Edwards EST EC-30DU-3 is a Photoelectric Duct Smoke Detector designed for use with 6260A-CU Duct Smoke Detector Housing. Operating Voltage Range: 14 - 30 VDC COMPATIBLE BASES and ACCESSORIES: — CRB4U-1 Detector Relay Base — CSBU-1 Detector Standard Base — CSBU-3 Detector Resistor Base — 6263-EC Air Velocity Test Kit — EC-LED Fire Alarm LED Indicator — C-DTS Fire Alarm LED/Test Station
-
Product Description NOTE: This part is discontinued by the manufacturer. No direct replacement is available. The EST EC30U-3 is a low-profile plug-in photoelectric detector is part of EST's EC Series of low-profile plug-in smoke and heat detectors. COMPATIBLE BASES sold separately: — CSBU-1 Standard detector base — CSB4U-1 4" standard detector base — CRB4U-1 4" relay detector base, 1.25A @ 30 Vdc
-
Product Description The Edwards EST EGCF-VM is a Genesis Ceiling Strobe, 15 to 95 multi-cd, white, with FIRE marking.
-
Product Description The Edwards EST1-1Z1 is a Single Zone conventional Fire Alarm Control Panel.
-
-
Product Description This is the Replacement Board for the EST FS-502 FireShield 5-Zone Conventional Fire Alarm Control Panel. Features 5 Class B IDC's and 2 Class B NACs, 120V AC Built In Keypad
-
Product Description Edwards EST FS1004GD FireShield is a 10-Zone conventional FACP with FSDACT. Supports 10 IDCs and 4 NACs. Grey Cabinet enclosure included.
-
Product Description The Edwards FSRSI is a remote system indicator for F-series fire alarm control panels. The FSRSI provides five LEDs and a buzzer to indicate AC power status, alarm events, supervisory events, trouble events, and ground fault events. The FSRSI also provides a local silence button to turn the buzzer off without affecting the LED indicators. FSRSI remote system indicators include a cover plate for installation in a standard, single-gang electrical box. You can also install the FSRSI with one or two remote zone indicators in an approved 2-, 3-, or 4-gang electrical box. Cover plates for 2-, 3-, or 4-gang electrical boxes (model numbers FSAT2, FSAT3, or FSAT4) are ordered separately.
-
Product Description The Edwards FSRZI-A FireShield Remote Zone Indicator is used to indicate zones in the alarm state. It contains five red LEDs. Compatible for use with Edwards FireShield Plus Conventional Fire Alarm Control Panels (E-FSC Series panels).
-
Product Description The Edwards EST G4-S7VM is a white Speaker Strobe for wall mounting, 70Vrms The speaker includes a field configurable switch for selecting both the desired wattage (2 W, 1 W, 1/2 W, or 1/4 W) and candela output (15, 30, 75 and 110 candela) COMPATIBLE Strobe Synchronization Modules: — SIGA-CC1S — SIGA-MCC1S — SIGA-CC1S-LG — SIGA-MCC1S-LG — ADTG1M-RM — MG1M-RM — EG1M-RM — XLSG1M-RM — G1M-RM — ZG1M-RM — G1M-RM-LG Mounts to 4" square electrical box.
-
Product Description The Edwards EST G4ERA-A Strobe Expander w/ multi-candela Strobe allows a speaker and two independent strobes to be installed in a single compact footprint. Compatible for use with G4RF-S2, G4RF-S2VM, G4RF-S7, G4RF-S7VM. The Edwards EST G4ERA-A is intended for indoor use only. Flush mounts to a recessed standard 4” square electrical box (minimum 1.5” deep). Surface mounting using the optional G4ERB (red) backbox.
-
Product Description The G4E Strobe Expander (White) provides a separate, independently-controlled strobe that fits readily behind a Genesis G4 Series speaker or speaker-strobe. Compatible for use with these G4 appliances: G4F-S2, G4F-S2VM, G4F-S7, G4F-S7VM
-
Product Description Edwards EST G4F-S7VM Speaker-Strobe
-
Product Description Edwards EST G4RB Surface Box
-
Product Description The Edwards EST G4RF-S2VM is a red FIRE Speaker. Part of the Genesis G4 Series. 25 Volt (Selectable 1⁄4, 1⁄2, 1, or 2 watt)
