Product Description The Edwards 897B-004 is a red Surface Backbox. Dimensions: 4.5 X 6.5 X 2.75"

Product Description Edwards 897B-005 Surface Backbox

Product Description Edwards 98BC-G1 Light Duty Strobe, Weatherpoof

Product Description The Edwards EST AB4G-SB Surface Backbox is compatible for use with AB4G Audible Detector Base.

Product Description The EST BPS-10A Booster Power Supply (10 amp) is designed to extend the signaling capacity of a fire alarm, security, or access control system. The BPSs can be connected to existing Class A or Class B notification appliance circuits (NACs) or activated via option modules. The BPSs can either pass or generate synchronization signals for Genesis sync strobes. The BPSs have four independent NAC/AUX circuits that are supervised when configured for NAC, plus a trouble relay. The input circuits of the booster power supply can be connected to 12 VDC or 24 VDC systems.

Product Description The EST BPS6A Booster Power Supply (6.5 amp) is designed to extend the signaling capacity of a fire alarm, security, or access control system. The BPSs can be connected to existing Class A or Class B notification appliance circuits (NACs) or activated via option modules. The BPSs can either pass or generate synchronization signals for Genesis sync strobes. The BPSs have four independent NAC/AUX circuits that are supervised when configured for NAC, plus a trouble relay. The input circuits of the booster power supply can be connected to 12 VDC or 24 VDC systems. Cabinet included.

Product Description Edwards EST's CSBU-1 Standard Detector Base is designed for use with Edwards / EST's EC Series Smoke and Heat Detectors. Provides plug-in tamper-resistant mounting. Includes screw terminals for connection of installation wires. COMPATIBLE EC SERIES DETECTOR HEADS: — EC30U-3 Low-profile plug-in Photoelectric Detector — EC10C-3 Low-profile Plug-in Ionization Detector — EC20FTU-3 Low-profile Plug-in Fixed Temperature Heat Detector — EC20RRU-3 Low-profile Plug-in Rate-of-Rise Heat Detector COMPATIBLE ACCESORIES: — C-TRIM Trim skirt for CSBU-1 base — EC-LED Remote alarm LED indicator

Product Description The Edwards EST CSBU-3 is a plug-in Detector Base (w/ Resistor) is intended for use with the EC Series of low-profile plug-in smoke and heat detectors from Edwards EST.

Product Description The Edwards EST E-NAC Analog NAC Module is an analog addressable device used to connect a supervised output circuit to a signal riser. The output wiring is monitored for open and short circuits. A short circuit causes the module to inhibit the activation of the audible/visual signal circuit so the riser is not connected to the wiring fault. Upon command from the control panel, the module connects the output circuit to the riser input. The output circuit energizes a riser to operate polarized audible and visual signals. The module can be used for connection of a Class A or Class B (with EOL) output notification appliance circuit (NAC). The device address is set using the two rotary switches located on the front of the module. One device address is required.

Product Description Edwards EC-LED Remote Alarm Indicator

Product Description Edwards EST EG4F-S7 70-volt Speaker (White) is part of the Genesis G4 Series of Speakers and Strobes.

Product Description The Edwards EST ESD-4WJ SuperDuct Four-Wire Duct Smoke Detector is a combination four-wire controller and sensor with RJ-45 modular connectors. COMPATIBLE ACCESSORIES: — SD-T8 Air sample tube, 8 inch — SD-T18 Air sample tube, 18 inch — SD-T24 Air sample tube, 24 inch — SD-T36 Air sample tube, 36 inch — SD-T42 Air sample tube, 42 inch — SD-T60 Air sample tube, 60 inch — SD-T78 Air sample tube, 78 inch — SD-T120 Air sample tube, 120 inch — SD-RJ15 RJ45 wiring harness kit -- 15 ft. — SD-RJ10 RJ45 wiring harness kit -- 10 ft. — SD-RJ5 RJ45 wiring harness kit -- 5 ft. — SD-TRM4 Remote test/reset station, magnetic — SD-TRK4 Remote test/reset station, keyed — 5956A Remote LED Alarm Indicator