-
Product Description The Edwards E-IDC1B Analog Single Input Mini Module connects a normally open, alarm, supervisory, or monitor type dry contact initiating device circuit (IDC) to the Edwards Signaling control panel. For Class B circuit operation. -
Product Description Edwards E-IDC1A Analog Class A Single Input Module is an analog addressable device used to connect a normally open, alarm, supervisory, or monitor type dry contact initiating device circuit (IDC) to a control panel. This module is designed for Class A circuit operation. The device address is set using the two rotary switches located on the front of the module. One device address is required. The device can be preset for alarm or supervisory operation using the slide switch located on the front of the module. The module can also be configured for other device types through front panel programming or the configuration utility.
-
Product Description The Edwards E-270 Addressable Manual Pull Station is a normally open dry contact initiating device that requires one action by the user to initiate an alarm. Rotary Addressing for use with Edwards Signalling intelligent systems.
-
Product Description NOTE: This part is discontinued by the manufacturer. There is no designated replacement. The Edwards DLD Dual Line Dialer provides two telephone line connections for transmitting system status changes to one or two compatible digital alarm communicator receivers (DACRs) over the public switched telephone network. For use with QS FACPs.
-
Product Description Edwards EST DHS-1224C Chrome Door Holder
-
Product Description The Edwards EST CSBU-3 is a plug-in Detector Base (w/ Resistor) is intended for use with the EC Series of low-profile plug-in smoke and heat detectors from Edwards EST.
-
Product Description Edwards EST's CSBU-1 Standard Detector Base is designed for use with Edwards / EST's EC Series Smoke and Heat Detectors. Provides plug-in tamper-resistant mounting. Includes screw terminals for connection of installation wires. COMPATIBLE EC SERIES DETECTOR HEADS: — EC30U-3 Low-profile plug-in Photoelectric Detector — EC10C-3 Low-profile Plug-in Ionization Detector — EC20FTU-3 Low-profile Plug-in Fixed Temperature Heat Detector — EC20RRU-3 Low-profile Plug-in Rate-of-Rise Heat Detector COMPATIBLE ACCESORIES: — C-TRIM Trim skirt for CSBU-1 base — EC-LED Remote alarm LED indicator
-
Product Description Edwards CS2002-11 Manual Yellow Pull Station
-
Product Description The Edwards EST CRB4U-1 is a 4" relay detector base (1.25A @ 30 Vdc) for use with Edwards EST EC Series of Smoke and Heat Detectors.
-
Product Description The Edwards CF200-EWT is an Explosion-Proof Fixed Temperature Heat Detector. Model CF-200-EWT is rated for 200F (93C) Contacts: Single Pole Normally Open - Rated at: 3.0 amps at 6 to 125VAC; 1.0 amps at 6 to 28VDC; 0.3 amps at 125VDC; 0.1 amp at 250VDC.
-
Product Description The Edwards EST C-DTS is a Detector Test Station, single-gang, flush mount.
-
Product Description The Edwards EST BPSIMA is a Class "A" Booster Power Supply Interface Module.
-
Product Description The Edwards EST BPSIM is a Booster Power Supply Interface Module for use in Edwards EST Fire Alarm Control Panels.
-
Product Description This is the Replacement Board for the Edwards EST BPS6A Booster Power Supply (6.5 amp) is designed to extend the signaling capacity of a fire alarm, security, or access control system. The BPSs can be connected to existing Class A or Class B notification appliance circuits (NACs) or activated via option modules. The BPSs can either pass or generate synchronization signals for Genesis sync strobes. The BPSs have four independent NAC/AUX circuits that are supervised when configured for NAC, plus a trouble relay. The input circuits of the booster power supply can be connected to 12 VDC or 24 VDC systems.
-
Product Description The EST BPS6A Booster Power Supply (6.5 amp) is designed to extend the signaling capacity of a fire alarm, security, or access control system. The BPSs can be connected to existing Class A or Class B notification appliance circuits (NACs) or activated via option modules. The BPSs can either pass or generate synchronization signals for Genesis sync strobes. The BPSs have four independent NAC/AUX circuits that are supervised when configured for NAC, plus a trouble relay. The input circuits of the booster power supply can be connected to 12 VDC or 24 VDC systems. Cabinet included.
-
Product Description The EST BPS-10A Booster Power Supply (10 amp) is designed to extend the signaling capacity of a fire alarm, security, or access control system. The BPSs can be connected to existing Class A or Class B notification appliance circuits (NACs) or activated via option modules. The BPSs can either pass or generate synchronization signals for Genesis sync strobes. The BPSs have four independent NAC / AUX circuits that are supervised when configured for NAC, plus a trouble relay. The input circuits of the booster power supply can be connected to 12 VDC or 24 VDC systems.
