-
Product Description The Edwards EST WG4RF-S is a red Evacuation Speaker marked "FIRE." 25/70V RMS Operating Voltage -
Product Description The Edwards Adaptabel 340-6N5 6-inch AC Vibrating Bell produces a long continuous sound. Power requirements: 120VAC / .070Amps PLC Compatible Mounts directly on surface or electrical box with Universal Adaptaplate.
-
Product Description Edwards 047327-0242-X1 Replacement Board
-
Product Description Edwards 130336P
-
Product Description Edwards EST 140279 ADMM Annunciator Driver Master Module
-
Product Description Edwards Signaling 1500-1 Door Holder Extension Rods are for use where it is desired to hold doors open and where a standoff distance between the magnet assembly and the armature base is required. The extension kit can be used with Edwards 1504, 1505, 1508 and 1509 series door holders. 1.5" Extension
-
Product Description Edwards EST 1534-1 Key-operated Fire Alarm Station is fitted with a key-operated switch of which the key is not easily duplicated. Stations use spanner head screws for mounting to the backbox. The 1534-1 has one Single Pole Normally Open contact rated for 1 amp at 24 Vdc. Features a 6-inch (150mm) wire leads for easy field wiring. They key can be removed in both the “ON” and “OFF” positions. Flush mounts to any standard North American 1-gang electrical box 2-1/2 inch (63mm) deep minimum, or surface mounts to Edwards 46292- 0200 Surface Mount Backbox.
-
Product Description Edwards EST 2-LCD Fire Alarm Display
-
Product Description The Edwards EST 2-CPU is a command point for remote annunciators in the EST2 network, and acts as the primary interface between the network and remote annunciators.
-
Product Description Edwards EST 2-LCD Fire Alarm Display Module
-
Product Description The Edwards EST 2-LCX Expander Loop Module is intended for use with the EST2 Fire Alarm Control Panel. Features 2 NCA (Notification Appliance Circuits) and 2 SDC (Signature Data Circuits). Requires programming.
-
Product Description The Edwards EST 2-LCX is the Signature Loop Card for the EST2 intelligent FACP.
-
Product Description The Edwards EST 2-PPS is the Primary Power Supply Module for use with the EST 2 Fire Alarm Control Panel.
-
Product Description Edwards EST 2-PPS/6A Primary Power Supply Module [NEW]
-
Product Description Edwards EST 202-8A-T Strobe
-
Product Description Edwards 130279P 2400 is the annunciator driver module for the ESL 2400 Fire Alarm Control Panel.
-
Product Description The Edwards 2430 is a conventional Photoelectric Smoke Detector. Power: 16V - 29V DC (22V nominal) Flush mounted using a standard 3 1/2" (89mm) by 1 1/2" (38mm) deep or 4" (102mm) by 1 1/2 (38mm) deep octagon box.
-
Product Description Edwards EST 2551FHR Photoelectric Smoke Detector for Duct Housings
-
Product Description The Edwards EST 2551F is a Plug-in Intelligent Photoelectronic Smoke Detector.
-
Product Description Edwards 276A-REL Manual Release Station is a normally-open, dry contact signal initiating device. The 276A-REL is a single-action station that requires the user to pull the release handle to initiate the release of a fire suppression agent.
-
Product Description The Edwards EST 278A-REL is a yellow dual-action Manual Release Station.
-
Product Description The Edwards 281B-PL is a Heat Detector (ROR and Fixed) Replacement for Edwards 281C. This unit has been discontinued and replaced by the Edwards 283B-PL. Rate of rise rating: 15F/min. Fixed Temp rating: 135F Single circuit normally open contact rated at 3 amps at 6 to 125V AC; 1.0 amps at 6 to 28V DC, 0.3 amps at 125V DC, and .01 amps at 250V DC Includes: 280A-PL Plastic Mounting Plate. Detector twists and locks onto mounting plate. Mounting plate may be surface mounted or mounted onto any 3 1/4" (83mm) or 4" (102mm) octagon box.
-
Product Description Edwards EST 282B-PL is a rate-of-rise and fixed temperature (194F) Heat Detector with a white plastic reversible mounting plate. The plastic plate can be used for either flush or surface mounting. It includes a white skirt which covers the space between detector base. Conventional device featuring single pole, normally open contact.
-
Product Description Edwards EST 3-BBC/M is a Booster Power Supply / Charger with Local Rail Module. 120V 50/60 Hz. Takes one Footprint in wallbox and one local Rail module space. Supports one user interface module. Provides 7 amp at nominal 24V dc. Provides two 3.5 Amp auxiliary power limited output. For use with EST3 Integrated Multiplex Systems.
