-
Product Description The Edwards 4ZEXP 4 Zone Expansion Module provides 4 Zones (Class B) and open collector circuit per zone. For use with Edwards EST LSS4 Fire Alarm Control Panels. -
Product Description Edwards GE 3-SSDC Signature Driver Controller Module provides an intelligent interface between the 3-CPU3 module and Signature Series devices. Exclusively for use with the Signature Loop Controller.
-
Product Description The Edwards EST 3-BPS/M-230 is a Booster Power Supply w/ local rail module (230V 50/60 Hz) designed for use with EST3 FACPs.
-
Product Description This is the Replacement Board for the Edwards EST EST3 Multiplexed Fire Alarm Control Panel. The Edwards EST 3-CPU3 Central Processor Module is the control element for all rail modules and control/display modules installed in a EST3 Multiplexed Fire Alarm Control Panel. NOTE: The 3-CPU3 is a replacement for the 3-CPU module and the 3-CPU1 module.
-
Product Description Edwards EST 3-BBC/M is a Booster Power Supply / Charger with Local Rail Module. 120V 50/60 Hz. Takes one Footprint in wallbox and one local Rail module space. Supports one user interface module. Provides 7 amp at nominal 24V dc. Provides two 3.5 Amp auxiliary power limited output. For use with EST3 Integrated Multiplex Systems.
-
Product Description Edwards EST 282B-PL is a rate-of-rise and fixed temperature (194F) Heat Detector with a white plastic reversible mounting plate. The plastic plate can be used for either flush or surface mounting. It includes a white skirt which covers the space between detector base. Conventional device featuring single pole, normally open contact.
-
Product Description The Edwards EST 278A-REL is a yellow dual-action Manual Release Station.
-
Product Description The Edwards 281B-PL is a Heat Detector (ROR and Fixed) Replacement for Edwards 281C. This unit has been discontinued and replaced by the Edwards 283B-PL. Rate of rise rating: 15F/min. Fixed Temp rating: 135F Single circuit normally open contact rated at 3 amps at 6 to 125V AC; 1.0 amps at 6 to 28V DC, 0.3 amps at 125V DC, and .01 amps at 250V DC Includes: 280A-PL Plastic Mounting Plate. Detector twists and locks onto mounting plate. Mounting plate may be surface mounted or mounted onto any 3 1/4" (83mm) or 4" (102mm) octagon box.
-
Product Description Edwards 276A-REL Manual Release Station is a normally-open, dry contact signal initiating device. The 276A-REL is a single-action station that requires the user to pull the release handle to initiate the release of a fire suppression agent.
-
Product Description The Edwards EST 2551F is a Plug-in Intelligent Photoelectronic Smoke Detector.
-
Product Description Edwards EST 2551FHR Photoelectric Smoke Detector for Duct Housings
-
Product Description The Edwards 2430 is a conventional Photoelectric Smoke Detector. Power: 16V - 29V DC (22V nominal) Flush mounted using a standard 3 1/2" (89mm) by 1 1/2" (38mm) deep or 4" (102mm) by 1 1/2 (38mm) deep octagon box.
-
Product Description Edwards EST 202-8A-T Strobe
-
Product Description Edwards 130279P 2400 is the annunciator driver module for the ESL 2400 Fire Alarm Control Panel.
-
Product Description Edwards EST 2-PPS/6A Primary Power Supply Module [NEW]
-
Product Description The Edwards EST 2-PPS is the Primary Power Supply Module for use with the EST 2 Fire Alarm Control Panel.
-
Product Description The Edwards EST 2-LCX Expander Loop Module is intended for use with the EST2 Fire Alarm Control Panel. Features 2 NCA (Notification Appliance Circuits) and 2 SDC (Signature Data Circuits). Requires programming.
-
Product Description The Edwards EST 2-LCX is the Signature Loop Card for the EST2 intelligent FACP.
-
Product Description Edwards EST 2-LCD Fire Alarm Display Module
-
Product Description The Edwards EST 2-CPU is a command point for remote annunciators in the EST2 network, and acts as the primary interface between the network and remote annunciators.
-
Product Description Edwards EST 2-LCD Fire Alarm Display
-
Product Description Edwards EST 1534-1 Key-operated Fire Alarm Station is fitted with a key-operated switch of which the key is not easily duplicated. Stations use spanner head screws for mounting to the backbox. The 1534-1 has one Single Pole Normally Open contact rated for 1 amp at 24 Vdc. Features a 6-inch (150mm) wire leads for easy field wiring. They key can be removed in both the “ON” and “OFF” positions. Flush mounts to any standard North American 1-gang electrical box 2-1/2 inch (63mm) deep minimum, or surface mounts to Edwards 46292- 0200 Surface Mount Backbox.
-
Product Description Edwards Signaling 1500-1 Door Holder Extension Rods are for use where it is desired to hold doors open and where a standoff distance between the magnet assembly and the armature base is required. The extension kit can be used with Edwards 1504, 1505, 1508 and 1509 series door holders. 1.5" Extension
-
Product Description Edwards EST 140279 ADMM Annunciator Driver Master Module
-
Product Description Edwards 130336P
-
Product Description The Edwards Adaptabel 340-6N5 6-inch AC Vibrating Bell produces a long continuous sound. Power requirements: 120VAC / .070Amps PLC Compatible Mounts directly on surface or electrical box with Universal Adaptaplate.
-
Product Description Edwards 047327-0242-X1 Replacement Board
-
Product Description The Edwards EST WG4RF-HVMC is a red Outdoor/Indoor Horn Strobe for wall or ceiling mounting. COMPATIBLE ACCESSORIES — WG4RTS Surface trim skirt, red — WG4GSKT Full Body Mounting Gasket for smooth surfaces
-
Product Description The Edwards EST WG4RF-S is a red Evacuation Speaker marked "FIRE." 25/70V RMS Operating Voltage
-
Product Description The Edwards EST WG4GSKT is a Full Body Mounting Gasket for smooth surfaces. Designed for use with Genesis WG4 Series Notification Appliances.
-
Product Description NOTE: This part is discontinued by the manufacturer. No direct replacement is recommended. Edwards EST SLIC Signature Loop Intelligent Controller Card Module is intended for use with QuickStart Series FACPs.
-
Product Description The Edwards SWU-8 is a Remote Annunciator Lamp and Switch Module.
-
Product Description NOTE: This part is discontinued by the manufacturer. Replace with: SIGA-OSHCD. The Edwards EST SIGA2-PHCOS is an Intelligent Multisensor Photoelectric/Heat Detector with Carbon Monoxide Sensor. Designed for use with the Signature Loop Controller. COMPATIBLE BASES and ACCESSORIES: — SIGA-SB Detector Mounting Base - Standard — SIGA-SB4 4-inch Detector Mounting Base w/ SIGA-TS4 Trim Skirt — SIGA-RB Detector Mounting Base w/Relay — SIGA-RB4 4-inch Detector Mounting Base w/Relay w/ SIGA-TS4 Trim Skirt — SIGA-IB Detector Mounting Base w/Fault Isolator — SIGA-IB4 4-inch Detector Mounting Base w/ Fault Isolator and SIGA-TS4 Trim Skirt — SIGA-LED Remote Alarm LED. (Connects to the SIGA-SB or SIGA-SB4 Standard Base only.) — SIGA-AB4G Audible (Sounder) Base for Fire Detectors — SIGA-AB4GT Audible (Sounder) Base for CO and Fire Detectors — SIGA-TCDR Temporal Pattern Generator — SIGA-CRR Polarity Reversal Relay can be used for sounding to other audible bases on the same 24 Vdc circuit. — SIGA-TS4 Trim Skirt (supplied with 4-inch bases) — SIGA-DMP Detector Mounting Plate — SIGA-RTA Detector Removal Tool — SIGA-VA Detector Cleaning Tool
-
Product Description NOTE: This part is discontinued by the manufacturer. Replace with SIGA-PHD, or SIGA-PHS for applications that do not require split photo/heat operation. Edwards EST SIGA2-PHS Intelligent Second Generation 3D Multisensor - Photoelectric, Heat COMPATIBLE BASES and ACCESSORIES: — SIGA-SB Detector Mounting Base - Standard — SIGA-SB4 4-inch Detector Mounting Base w/ SIGA-TS4 Trim Skirt — SIGA-RB Detector Mounting Base w/Relay — SIGA-RB4 4-inch Detector Mounting Base w/Relay w/ SIGA-TS4 Trim Skirt — SIGA-IB Detector Mounting Base w/Fault Isolator — SIGA-IB4 4-inch Detector Mounting Base w/ Fault Isolator and SIGA-TS4 Trim Skirt — SIGA-LED Remote Alarm LED. (Connects to the SIGA-SB or SIGA-SB4 Standard Base only.) — SIGA-AB4G Audible (Sounder) Base for Fire Detectors — SIGA-AB4GT Audible (Sounder) Base for CO and Fire Detectors — SIGA-TCDR Temporal Pattern Generator — SIGA-CRR Polarity Reversal Relay can be used for sounding to other audible bases on the same 24 Vdc circuit. — SIGA-TS4 Trim Skirt (supplied with 4-inch bases) — SIGA-DMP Detector Mounting Plate — SIGA-RTA Detector Removal Tool — SIGA-VA Detector Cleaning Tool
-
Product Description NOTE: This part is discontinued by the manufacturer. Replace with — SIGA-HRD — SIGA-HRS Edwards EST SIGA2-HRS Intelligent Fixed and Rate-of-Rise Heat Detector provides a 15 °F (9 °C) per minute rate-of-rise heat sensor for the detection of heat due to fire. The SIGA2-HRS is part of GE's Signature Series of Intelligent Heat Detectors with Optional CO Sensors. For use with Signature Loop Controller. COMPATIBLE BASES and ACCESSORIES: — SIGA-SB Detector Mounting Base - Standard — SIGA-SB4 4-inch Detector Mounting Base w/ SIGA-TS4 Trim Skirt — SIGA-RB Detector Mounting Base w/Relay — SIGA-RB4 4-inch Detector Mounting Base w/Relay w/ SIGA-TS4 Trim Skirt — SIGA-IB Detector Mounting Base w/Fault Isolator — SIGA-IB4 4-inch Detector Mounting Base w/ Fault Isolator and SIGA-TS4 Trim Skirt — SIGA-LED Remote Alarm LED. (Connects to the SIGA-SB or SIGA-SB4 Standard Base only.) — SIGA-AB4G Audible (Sounder) Base for Fire Detectors — SIGA-AB4GT Audible (Sounder) Base for CO and Fire Detectors — SIGA-TCDR Temporal Pattern Generator — SIGA-CRR Polarity Reversal Relay can be used for sounding to other audible bases on the same 24 Vdc circuit. — SIGA-TS4 Trim Skirt (supplied with 4-inch bases) — SIGA-DMP Detector Mounting Plate — SIGA-RTA Detector Removal Tool — SIGA-VA Detector Cleaning Tool — 2-CORPL Replacement CO Sensor
-
Product Description NOTE: This part is discontinued by the manufacturer. Replace with — SIGA-HFD — SIGA HFS Edwards EST SIGA2-HFS Fixed Temperature Heat Detectors are only for use with Signature Loop Controller. Fixed temperature (135F) or rate-of-rise heat detection with optional carbon monoxide sensor. COMPATIBLE BASES and ACCESSORIES: — SIGA-SB Detector Mounting Base - Standard — SIGA-SB4 4-inch Detector Mounting Base w/ SIGA-TS4 Trim Skirt — SIGA-RB Detector Mounting Base w/Relay — SIGA-RB4 4-inch Detector Mounting Base w/Relay w/ SIGA-TS4 Trim Skirt — SIGA-IB Detector Mounting Base w/Fault Isolator — SIGA-IB4 4-inch Detector Mounting Base w/ Fault Isolator and SIGA-TS4 Trim Skirt — SIGA-LED Remote Alarm LED. (Connects to the SIGA-SB or SIGA-SB4 Standard Base only.) — SIGA-AB4G Audible (Sounder) Base for Fire Detectors — SIGA-AB4GT Audible (Sounder) Base for CO and Fire Detectors — SIGA-TCDR Temporal Pattern Generator — SIGA-CRR Polarity Reversal Relay can be used for sounding to other audible bases on the same 24 Vdc circuit. — SIGA-TS4 Trim Skirt (supplied with 4-inch bases) — SIGA-DMP Detector Mounting Plate — SIGA-RTA Detector Removal Tool — SIGA-VA Detector Cleaning Tool — 2-CORPL Replacement CO Sensor
