-
Product Description The Edwards EST E-NAC Analog NAC Module is an analog addressable device used to connect a supervised output circuit to a signal riser. The output wiring is monitored for open and short circuits. A short circuit causes the module to inhibit the activation of the audible/visual signal circuit so the riser is not connected to the wiring fault. Upon command from the control panel, the module connects the output circuit to the riser input. The output circuit energizes a riser to operate polarized audible and visual signals. The module can be used for connection of a Class A or Class B (with EOL) output notification appliance circuit (NAC). The device address is set using the two rotary switches located on the front of the module. One device address is required. -
Product Description The Edwards E-PD Intelligent Analog Optical Smoke Detector uses rotary switches to set address. COMPATIBLE BASES and ACCESSORIES: — B4U Standard Base — RB4U Relay Detector Base — IB4U Isolator Detector Base — SB4U Audible (Sounder) Detector Base — AB4G-SB Surface Box for Audible Base — RLED Remote alarm LED, use with standard base only — 211-10PKG Replacement optical chambers
-
Product Description Edwards EC-100R Beam Detector Unit
-
Product Description Edwards EC-LED Remote Alarm Indicator
-
Product Description Edwards EST EC-LLT Low Level Tester
-
Product Description Edwards EST EC20RRU-3 Heat Detector
-
Product Description The Edwards EST EC-30DU-3 is a Photoelectric Duct Smoke Detector designed for use with 6260A-CU Duct Smoke Detector Housing. Operating Voltage Range: 14 - 30 VDC COMPATIBLE BASES and ACCESSORIES: — CRB4U-1 Detector Relay Base — CSBU-1 Detector Standard Base — CSBU-3 Detector Resistor Base — 6263-EC Air Velocity Test Kit — EC-LED Fire Alarm LED Indicator — C-DTS Fire Alarm LED/Test Station
-
Product Description NOTE: This part is discontinued by the manufacturer. No direct replacement is available. The EST EC30U-3 is a low-profile plug-in photoelectric detector is part of EST's EC Series of low-profile plug-in smoke and heat detectors. COMPATIBLE BASES sold separately: — CSBU-1 Standard detector base — CSB4U-1 4" standard detector base — CRB4U-1 4" relay detector base, 1.25A @ 30 Vdc
-
-
Product Description Edwards EST EG4F-S7 70-volt Speaker (White) is part of the Genesis G4 Series of Speakers and Strobes.
-
Product Description The Edwards EST EGCF-VM is a Genesis Ceiling Strobe, 15 to 95 multi-cd, white, with FIRE marking.
-
Product Description The Edwards EST ESD-4WJ SuperDuct Four-Wire Duct Smoke Detector is a combination four-wire controller and sensor with RJ-45 modular connectors. COMPATIBLE ACCESSORIES: — SD-T8 Air sample tube, 8 inch — SD-T18 Air sample tube, 18 inch — SD-T24 Air sample tube, 24 inch — SD-T36 Air sample tube, 36 inch — SD-T42 Air sample tube, 42 inch — SD-T60 Air sample tube, 60 inch — SD-T78 Air sample tube, 78 inch — SD-T120 Air sample tube, 120 inch — SD-RJ15 RJ45 wiring harness kit -- 15 ft. — SD-RJ10 RJ45 wiring harness kit -- 10 ft. — SD-RJ5 RJ45 wiring harness kit -- 5 ft. — SD-TRM4 Remote test/reset station, magnetic — SD-TRK4 Remote test/reset station, keyed — 5956A Remote LED Alarm Indicator
-
Product Description The Edwards EST ESD-SJ SuperDuct Duct Smoke Detector is a four-wire smoke sensor with RJ-45 modular connector for use with SuperDuct Series Duct Smoke Detectors.
-
Product Description The Edwards EST1-1Z1 is a Single Zone conventional Fire Alarm Control Panel.
-
Product Description The Edwards EST F-DACT is a digital alarm communicator transmitter for use with F-series fire alarm control panels. The F-DACT can be programmed to operate as a single or dual line DACT/Modem/LCD display, a Modem/LCD display, or an LCD display only.
-
Product Description The Edwards EST / GE F-XTR120 NAC Power Expander Transformer is intended for use with 10-zone, 120VAC F-Series fire alarm control panels. p/n 3101035
-
Product Description This is the replacement board for the EST Fireshield FS1004 (10-zone) fire alarm control panel; supports 10 initiating device circuits and 4 notification appliance circuits. Panel is configured for Class B operation. Can be converted to Class A by using two Class B circuits to make one Class A circuit. COMPATIBLE (OPTIONAL) ACCESSORIES: — Remote System Indicator (FSRSI) — Remote Zone Indicator (FSRZI-A) — Remote Relay Module (FSRRM) — Power Expander Transformer (XTR3A120, XTR3A230) — DACT (Dialer)/Modem (FSDACT) — City Tie Module (CTM4.7) — Reverse Polarity Module (RPM) — Battery Cabinet (BC-2)
-
-
Product Description This is the Replacement Board for the Edwards EST FS-302 FireShield 3-zone conventional Fire Alarm Control Panel. Supports 3 IDCs and 2 NACs. Old Style Boards have a Built-in Keypad. COMPATIBLE ACCESSORIES: — Remote System Indicator (FSRSI) — Remote Zone Indicator (FSRZI-A) — Remote Relay Module (FSRRM) — Power Expander Transformer (XTR3A120, XTR3A230) (ten-zone only) — DACT (Dialer)/Modem (FSDACT) — City Tie Module (CTM4.7) — Reverse Polarity Module (RPM) — Battery Cabinet (BC-2)000
-
Product Description This is the Replacement Board for the EST FS-502 FireShield 5-Zone Conventional Fire Alarm Control Panel. Features 5 Class B IDC's and 2 Class B NACs, 120V AC Built In Keypad
-
Product Description Edwards EST FS1004GD FireShield is a 10-Zone conventional FACP with FSDACT. Supports 10 IDCs and 4 NACs. Grey Cabinet enclosure included.
-
Product Description The Edwards EST FS1004RD FireShield is a 10-Zone conventional FACP with FSDACT. Supports 10 IDCs and 4 NACs. Red Cabinet enclosure included.
-
Product Description The Edwards EST FSAT3 is a Remote Annunciator Wall Plate, Three Gang (White) for use with FSRSI and FSRZI-A Remote Annuciators.
-
-
Product Description NOTE: This part is discontinued by the manufacturer. No direct replacement recommended. The Edwards EST FSP502GD FireSheild Plus (FACP) is a Conventional Fire Alarm Control Panel – 5 Class B IDCs and 2 Class B NACs (Pairs of IDCs and NACs convertible to single Class A circuits) 120VAC operation "GD" = Includes Grey Cabinet and Dialer
-
Product Description NOTE: This part is discontinued by the manufacturer. No direct replacement recommended. The Edwards EST FSP502R FireSheild Plus (FACP) is a Conventional Fire Alarm Control Panel – 5 Class B IDCs and 2 Class B NACs (Pairs of IDCs and NACs convertible to single Class A circuits) 120VAC operation "R" = Red Cabinet
-
Product Description The Edwards FSRSI is a remote system indicator for F-series fire alarm control panels. The FSRSI provides five LEDs and a buzzer to indicate AC power status, alarm events, supervisory events, trouble events, and ground fault events. The FSRSI also provides a local silence button to turn the buzzer off without affecting the LED indicators. FSRSI remote system indicators include a cover plate for installation in a standard, single-gang electrical box. You can also install the FSRSI with one or two remote zone indicators in an approved 2-, 3-, or 4-gang electrical box. Cover plates for 2-, 3-, or 4-gang electrical boxes (model numbers FSAT2, FSAT3, or FSAT4) are ordered separately.
-
Product Description The Edwards FSRZI-A FireShield Remote Zone Indicator is used to indicate zones in the alarm state. It contains five red LEDs. Compatible for use with Edwards FireShield Plus Conventional Fire Alarm Control Panels (E-FSC Series panels).
-
-
Product Description The Edwards EST G1-HDVM is a white multi-candela Horn Strobe for wall mounting, 24VDC
-
Product Description Edwards EST G1-P is a white 24VDC Genesis Steady Horn designed for wall mounting. COMPATIBLE ACCESSORIES: — 27193-16 One-gang Surface Mount Box (white) — G1T Genesis Trim Plate for 2-gang or 4" square boxes (white) — G1T-FIRE Genesis Trim Plate with “FIRE” markings for 2-gang or 4" square boxes (white) — G1T-SB Surface box used for surface mounting (white) NOTE: The G1-P is not compatible with Genesis Signal Master.
-
Product Description Edwards EST G1-VM Genesis Multi-CD Strobe features selectable 15, 30, 75, or 110 cd output. VOLTAGE: non-coded, filtered 16 - 33 Vdc or unfiltered 16-33 Vdc FWR COMPATIBLE SYNCHRONIZATION MODULES: —G1M Genesis Signal Master — Snap-on Mount —G1M-RM Genesis Signal Master — Remote Mount (1-gang) —SIGA-CC1S Intelligent Synchronization Output Module (2-gang) —SIGA-MCC1S Intelligent Synchronization Output Module (Plug-in UIO)
-
-
-
Product Description Edwards EST G1F-HDVM Multi-candela Genesis Horn Strobe Selectable 15, 30, 75, or 110 cd output Selectable high/low dB output COMPATIBLE SYNCH MODULES — G1M Genesis Signal Master — Snap-on Mount 0.2 (0.1) — G1M-RM Genesis Signal Master — Remote Mount (1-gang) — SIGA-CC1S Intelligent Synchronization Output Module (2-gang) 0.5 (0.23) — SIGA-MCC1S Intelligent Synchronization Output Module (Plug-in UIO)
-
Product Description Edwards EST G1F-VM Genesis Strobe Selectable 15, 30, 75, or 110 cd output COMPATIBLE SYNCH MODULES — G1M Genesis Signal Master — Snap-on Mount 0.2 (0.1) — G1M-RM Genesis Signal Master — Remote Mount (1-gang) — SIGA-CC1S Intelligent Synchronization Output Module (2-gang) 0.5 (0.23) — SIGA-MCC1S Intelligent Synchronization Output Module (Plug-in UIO)
