-
Key Features:; Beacon with Integral Base Non Addressed - dedicated for use with EV-PYS -
Optical Detector with built in Sounder Sounder ~ 88dB(A) @ ~ 3.5mA Drive Output for dedicated EV-PSBCN Evolution FSK protocol EEPROM Addressed (Programmer)
-
Key Features:; Evolution FSK Protocol EEPROM Addressed (Programmer) 12 Tones DIP Switch Selected (3 Approved Tones) Replaces EV-ABS Sounder Standalone device, not for use with Detector
-
Key Features:; Evolution FSK Protocol EEPROM Addressed (Programmer) 12 Tones DIP Switch Selected (3 Approved Tones) Replaces EV-ABS Sounder
-
Key Features:; Dual Optical Detector Reduces False Alarms Omniview 360° LED Internal Alarm Current Limiting Resistor Wide Operational Voltage Range (16v-32v)
-
Installation:; Low profile, stylish appearance Different response grades available Non-polarised terminals Unauthorised head removal signal facility Low monitoring current Patented OMNIVIEW™ 360º LED alarm indicator Remote indicator output Compatible with UB-4, UB-4SD and STB-4SE bases
-
Key Features:; 62°C and 92°C Heat Detectors Omniview 360° LED Internal Alarm Current Limiting Resistor Wide Operational Voltage Range (11v-32v)
-
Key Features:; Dual Band IR Flame Detector Omniview 360° LED Internal Alarm Current Limiting Resistor Wide Operational Voltage Range (12v-32v); IR Flame Detector - Data Sheet
-
Key Features:; Intrinsically Safe Optical Detector Nittan Y Type Chamber Omniview 360° LED Operational Range (12v-32v) Limited to 28v by External Barrier Use UB-4-IS Base or EV-SPB-IS Base; IS Detector - Instructions IS Detector - Data Sheet
-
4.3 inch touch screen Easy to use configuration software Full cause and effect programming at Panel or PC Configuration tool Up to 254 devices on the loop 254 zones available Network Card built in for networking up to 16 panels Remote Access via the “Nittan Portal” (Future Development) 2 x configurable rs485 ports Up to 8 password protected users Switch mode power supply EN 54 part 2 and part 4
-
Key Features:; Dual Optical Technology Plus Heat Sensor Reduces False Alarms Evolution FSK Protocol EEPROM Addressed (Programmer) RIL and Base Control Outputs
-
20 programmable zonal / 25 System LEDs Nittan Evolution protocol Graphical LCD user interface and support for up to 200 fire zones by default allowing full EN54 compliance without additional hardware Dedicated USB & RS232 Serial Port for direct PC or modem connection Installer friendly Auto-learn, Loop Detection and On-board Scope facility for ease of commissioning and fault finding Graphical display configurable for virtually any language Robust removable equipment chassis with plug-in connectors for simple fixing and cable termination Integral P-Bus for system expansion via available option cards Ad-NeT peer-to-peer network with up to 2000 zones Approved to BS EN54 part 2 and 4
-
20 Programmable zonal / 25 System LEDs Nittan Evolution protocol Graphical LCD user interface and support for up to 200 fire zones by default allowing full EN54 compliance without additional hardware Dedicated USB & RS232 serial port for direct PC or modem connection Installer friendly Auto-learn, Loop Detection and On-board Scope facilities for ease of commissioning and fault finding Graphical display configurable for virtually any language Robust removable equipment chassis with plug-in connectors for simple fixing and cable termination Integral ‘P-Bus’ for system expansion via available option cards Ad-NeT peer-to-peer network with up to 2000 zones Approved to BS EN54 part 2 and 4
-
20 programmable Zonal / 25 System LEDs Nittan Evolution protocol Graphical LCD user interface and support for up to 200 fire zones by default allowing full EN54 compliance without additional hardware Dedicated USB & RS232 serial port for direct PC or modem connection Installer friendly Auto-learn, Loop Detection and On-board Scope facility for ease of commissioning and fault finding The graphical display can be configured to operate with virtually any language or character set Integral P-Bus for system expansion via available option cards Ad-NeT peer-to-peer network with up to 2000 zones Approved to BS EN54 part 2 and 4 Robust removable equipment chassis with plug-in connectors for simple fixing and cable termination
-
Key Features; Advanced, premium Smoke Detector Scattering Light detection Very small – 40mm(W) x 40mm(L) x 45mm(H) High degree of protection against unwanted false alarms Extremely reliable fire detection Use with CPC-3 Control Unit
-
Product Specification; Sensor Type: Manual Call Point Operating Voltage: 24v Standard: EN54-11 + ATEX Alarm Indication: None
-
Nittan RP-RS1-01/NTN Surface Mounting Reset Call Point IP24; EN54-11 approved (Cert No. 653a/01) Glass appearance maintains operator deterrence Positive activation that mimics the feel of breaking glass Visible warning flag confirms activation Simple key to reset operating element – no broken glass No glass elements to break lose or incorrectly fit during installation Complete functional test with every activation Extremely attractive, high value look and feel Low profile, heavy-duty terminations – Two built-in resistor values
-
Please Note: This is for the Black Box only
-
Thermistor Heat Sensor Robust Fully Modulated AS Communications Protocol DIL Switch Addressed
-
Thermistor Heat Sensor Omniview 360° Direct replacement for ST-H-AS Robust Fully Modulated AS Communications Protocol EEPROM addressed (Address stored in on-board EEPROM, programmed by handheld programmer)
-
Optical Smoke Detector Omniview 360° LED S/C Alarm characteristic Wide operational voltage range (12v - 32v)
-
Latest Generation Nittan Optical Chamber Omniview 360° LED Robust fully modulated AS Communications Protocol EEPROM addressed (Address stored in on-board EEPROM, programmed by handheld programmer) WILL REPLACE ST-P-AS
-
Deep Base 12v operation PCB mounted Relay Volt free C/O contacts
-
-
-
Manual Call point STI RESET Housing-IP24 Internal Alarm Current Limiting Resistor Wide Operational Voltage Range (12v-28v)
-
-
Nittan - Datasheet
-
-
-
-
Patented venturi pipe and duct housing One-pipe air sampling system Uniguard Superflow New cross-section (shape) of the venturi pipe gives an optimum of venturi effect Test hole on cover Simple installation Sensitive flow indicator Simple service and maintenance Installer-friendly connection of cables Foolproof installation of venturi pipe
-
Waterproof tested to IP67 Glass appearance maintains operator deterrence Positive activation that mimics the feel of breaking glass Visible warning flag confirms activation Simple key to reset operating element – no broken glass No glass elements to break, lose or incorrectly fit during installation Complete functional test with every activation Extremely attractive, high value look and feel Low profile, heavy-duty terminations – two built in resistor values
-
-
-
Modern design Clip together assembly Weatherproof kit option High “ring” output
-
Modern design Clip together assembly Weatherproof kit option High “ring” output; Suitable for all locations Easy to fit Provides protection up to IP44C with weather resistant option Easily identified signal
-
Modern design Clip together assembly Weatherproof kit option High “ring” output; Suitable for all locations Easy to fit Provides protection up to IP44C with weather resistant option Easily identified signal
-
Modern design Clip together assembly Weatherproof kit option High “ring” output; Suitable for all locations Easy to fit Provides protection up to IP44C with weather resistant option Easily identified signal
-
Faster installation - The large cable access, rear or surface cable entry options and innovative loop continuity spring all make for faster more cost effective installation. Reduced install errors and easy fault finding - devices are mounted using a positive push and turn engagement system and are supplied with an address tag for clear identification. Isolation is built-in to each device and addressing is made simple by familiar rotary wheel address controls. In addition each device incorporates an anti-tamper feature giving added security. Excellent system performance - High light output and a selection of 32 sounder tones can be synchronised via the Notifier control panel to provide fast clear warning of a fire related incident. Flexible installation - The low current draw of the devices enables more devices on each loop. This combined with the wide range of devices and mounting options including deep and high IP options, white or red colour options and sounder volume controllable from the panel or the sounder itself all make for greater flexibility for the system designer. Reduced lifetime costs - each device in the Opal AV range is constructed from high quality UV stable materials, designed for impact resistance and years of trouble free operation. If changes to a system are required the universal system base means a sounder/beacon can be added without re-wiring. Reduced inventory count - Notifier’s Opal AV range now utilizes the B501AP system base,- common to detectors. The Opal AV range is designed to maximise the features of Notifier’s advanced digital Opal protocol but remains backward compatible with previous Notifier communication protocols so can be used for retrofit and replacement for older systems. Opal AV devices provide both standard wall mounting units and integrated base units allowing the direct fitting of Notifier detectors. Wall mounting units are available as a sounder, sounder & beacon combination and a beacon only with sounder colour options of both red and white. Integrated base sounder units are also available as either a sounder or a sounder and beacon combination in colours to match the detectors.
-
-
-
-
-
-
-
-
